Another week and another month fly by in a flash it seems but we are making good progress and cutting the dock lines from here in beautiful sunny Finike Marina is getting closer with each passing day. This week also felt like summer is definately on its way with day time temp yesterday getting up to a new high of 29C/84F so we tropical birds are loving this change.
Nothing too visually exciting for this week’s Show & Tell update unfortunately but I’ll do my best to get you caught up on what all we did get done this past week of April 25-30, 2022.
Decks are Done!
One of the larger jobs that we are very thankful to have finished is that the team from Naval finished redoing all the TreadMaster on all our decks.
Despite being very high quality, the West Systems epoxy that was used to affix all the sheets of TreadMaster to the AL decks had not adhered to the AL very well so it has become both an eyesore and a tripping danger.
They carefully removed each panel of TM, sanded the AL down, applied Bostik Primer and then Bostik adhesive and glued them all back down with rollers.
Apologies for not having any photos of the completed decks but you get the idea.
Charging Issues
When my friend John was here two weeks ago we finished setting up and configuring the two WakeSpeed 500 regulators which control the two Electrodyne 250 Amp @ 24V alternators.
This upper Electrodyne is powered off of Mr. Gee’s crankshaft with a toothed “timing” belt.
The six large red cables carry the AC current from each alternator over to the Electrodyne Rectifiers which are mounted outside of the ER.Difficult to photograph this drive system I designed so this rendering of my CAD models will show it much better. Crankshaft pulley is at the bottom, sea water pump on the left and Electrodyne in the upper right. Works out eXtremely well as there is zero chance of any slippage of these toothed belts and I put in a spring loaded idler pulley (not shown in this render) which keeps the tension just right all the time.
Also difficult to photograph now all the floors are in the Engine Room, the lower Electrodyne is powered directly off of the PTO or Power Take Off that is on the lower left side of Mr. Gee. An eXtremely robust and almost maintenance free setup as well.
This older photo when Mr. Gee was up in the air shows how this PTO drive works.
I went with these massively large and strong Electrodyne alternators in large part because they use an external Rectifier which is what you see here.
The diodes in the rectifier are where the majority of the heat comes from in an alternator and heat is the enemy of electrical efficiency so keeping them out of the alternator and out of the ER really helps to increase the lifespan and efficiency of the whole charging system.
Each Rectifier is then connected to one of the WakeSpeed 500 Smart Regulators and each WS500 is interconnected with the white Ethernet cable you see here.
Connecting these two WS500’s is a big part of what makes them deservedly called “smart” because they then automatically figure out how to perfectly balance the charging from each alternator which can otherwise be quite difficult and prone to errors.However, the biggest reason these WS500’s are the first truly ‘Smart’ regulators is because they use both Voltage AND Amperage do monitor the batteries and adjust the alternators to produce the just right amount of charging.
With everything all wired up we started up Mr. Gee and after the initial ramp up time we were soon seeing about 220 Amps going into the 1800 Ah House Battery which was a joy to see.
Having two of these Electrodyne 250Ah alternators give us the potential for up to 12kW of electrical charging so in a way we actually do have a “generator” onboard.
Unfortunately we soon noticed that some of the 24V circuit breakers were tripping when these alternators were running and I’ve spent the past few weeks trying to figure out what was causing that. Thanks to exemplary help from both Dale at Electrodyne and Neil at WakeSpeed, both of whom have been fabulous to work with from the very beginning, I was eventually able to track down the problem to an incorrectly installed aluminium bar that was used to fasten the two halves of the Electrodyne Rectifiers. One end of this AL flat bar was touching one of the AL L-brackets that hold the studs and diode in the Rectifier. Once found the fix was pretty quick and easy.
However somewhere along the way one of the WS500’s stopped working so I am now working with Neil to sort that out. In the meantime we have up to 250Ah charging capacity from the one working Electrodyne/WS500 combo and with all the solar power we have coming out of our 14 solar panels, we have no need for any of it most of the time.
Exhausting work on Tender Mobli
Most of my time this week was spent finishing off the installation of the Yanmar 4JH4 HTE 110HP engine and Castoldi 224DD jet drive in our Tender that we have named “Mobli”.
Similar to Mr. Gee and most marine engines, the Yanmar uses a wet exhaust where sea water is injected into the exhaust gas after it exits the turbocharger. This water dramatically drops the temperature of the exhaust gasses so you can use rubber and fiberglass exhaust hoses to carry the gases and water out of the boat.
You can see the primary components I’m using to build the exhaust system in the photo below;water injection elbow on the Yanmar on the far Left with the Black rubber exhaust hose with the yellow stripe to carry the exhaust gas and water down to the cylindrical water muffler in the upper left.
I will use the two white RFP 90 degree elbows to carry the water/gas up and out of the boat through the 76mm/3” AL pipe on the right.
Like this.
I am waiting for more of the SS hose clamps to arrive but this is what the finished setup will look like. Will need to fabricate and install a bracket to hold the muffler in place as well and that will complete the exhaust system.
Hard to see (click to expand any photo) but I was also able to install the black rubber hose that you see running parallel to the left of the exhaust hose and muffler. This carries the cooling sea water from the housing of the Castoldi Jet drive up to the intake on the sea water pump on the left side of the Yanmar.
Last major job to complete the installation of the Yanmar/Castoldi propulsion system is the mounting of the battery and its cables to both the jet drive and the engine and I hope to get that done this coming week.
That’s how I spent my last week of April 2022 and hope yours was equally productive.
Thanks for taking the time to follow along, always encouraging to know you are all out there and along for the ride with Christine and me. Thanks in advance for typing any and all comments and questions in the “Join the Discussion” box below and hope you will join us again next week as we get May off to a good start.
-Wayne
Recent Comments